全自動超聲波清洗注意保持機械清潔干凈：專用超聲波清洗機一般安裝在某些特定物件清洗的生產流水線上，被清洗物件從進料口可傳動到不銹鋼專用網帶送人超聲波清洗槽清洗，在經噴淋、烘干等工序后出料，實現被清洗物件可直接包裝入庫。

Pay attention to keeping the machinery clean in automatic ultrasonic cleaning: the special ultrasonic cleaning machine is generally installed on the production line for cleaning some specific objects. The cleaned objects can be transmitted from the feeding port to the stainless steel special mesh belt and sent to the ultrasonic cleaning tank for cleaning. After spraying, drying and other processes, the materials are discharged, so that the cleaned objects can be directly packed and stored in the warehouse.

一臺清洗機用多個換能器，經粘接劑粘接在清洗剛底部且經并聯連接組成一臺清洗機的換能器，換能器基元之間距對頻率20kH4一般在5—10mm為佳，太大了容易產生彎曲振動，且振動板受到腐蝕，同時輻射面相對減少。

A cleaning machine uses multiple transducers, which are bonded to the bottom of the cleaning steel by adhesive and connected in parallel to form the transducer of a cleaning machine. The distance between the transducer elements and the frequency of 20kh4 is generally 5-10mm. If it is too large, it is easy to produce bending vibration, and the vibrating plate is corroded, and the radiation surface is relatively reduced.

嚴禁從超聲波控制柜頂端的進風口處濺入導電液體(如水)。否則會對清洗機的線路系統造成嚴重損害。超聲波清洗機注意保持機器清潔，不使用時關掉電源。避免對機器的碰撞或劇烈震動。遠離熱源。機器應避免在潮濕的環境下存放。

Do not splash conductive liquid (such as water) from the air inlet at the top of the ultrasonic control cabinet. Otherwise, it will cause serious damage to the circuit system of the cleaning machine. Pay attention to keep the ultrasonic cleaning machine clean and turn off the power when not in use. Avoid collision or violent vibration to the machine. Keep away from heat sources. The machine should not be stored in a humid environment.

機器連續工作時間不得超過4小時，如連續工作時間過長：應旋轉超聲調節旋鈕至“0”位，而讓散熱風扇繼續工作，在超聲波清洗不啟動的狀態下為超聲波控制柜內持續散熱至少2分鐘。

The continuous working time of the machine shall not exceed 4 hours. If the continuous working time is too long: rotate the ultrasonic adjusting knob to the "0" position, and let the cooling fan continue to work. When the ultrasonic cleaning is not started, the heat dissipation in the ultrasonic control cabinet shall be continued for at least 2 minutes.

經長時間運行的清洗機，在停機前應首先將功率旋鈕調至零位，使用其風機再工作3-6分鐘后關機，以保證電源內部熱量散出。清洗液應及時沉淀、過濾或更換，以保證清洗效果。

For the cleaning machine that has been operated for a long time, the power knob should be adjusted to zero before shutdown, and the fan should be used to work for another 3-6 minutes before shutdown, so as to ensure the internal heat dissipation of the power supply. The cleaning solution should be precipitated, filtered or replaced in time to ensure the cleaning effect.

超聲波發生器產生高頻高壓，通過電纜聯結線傳導給換能器，換能器與振動板一起產生高頻共振，超波清洗機主要由超聲波清洗槽和超聲波發生器兩部分構成。超聲波清洗槽用，底部安裝有超聲波換能器振子，堅固彈性好、耐腐蝕的優質不銹鋼制成；從而使清洗槽中的溶劑受超聲波作用對污垢進行洗凈。

The ultrasonic generator generates high-frequency and high-voltage, which is transmitted to the transducer through the cable connecting line. The transducer and the vibrating plate produce high-frequency resonance together. The ultrasonic cleaning machine is mainly composed of two parts: ultrasonic cleaning tank and ultrasonic generator. For ultrasonic cleaning tank, the bottom is equipped with ultrasonic transducer vibrator, which is made of solid, elastic and corrosion-resistant high-quality stainless steel; Thus, the solvent in the cleaning tank is cleaned by ultrasonic wave.

請勿用手去調節功率旋鈕，應確保功率旋鈕在小處，打開電源后，以免清洗液浸入電位器內部，超聲波清洗機大功率模塊啟動頻繁，對設備使用壽命有所影響。

Do not adjust the power knob by hand. Make sure the power knob is in a small place. After turning on the power supply, it will prevent the cleaning fluid from immersing in the potentiometer. The high-power module of the ultrasonic cleaner starts frequently, which will affect the service life of the equipment.

全自動超聲波清洗機的清洗池中的水位低于側面振板(清洗池長度方向側板的凸出部分)時，應先將功率旋鈕旋到小處工作2至3分鐘，造成該機無法正常工作或損壞設備。如運行中突然停電，請迅速關掉電源開關并將功率旋鈕旋至小處，以免重復停送電，嚴禁開機，否則會對清洗機造成嚴重傷害。

When the water level in the cleaning pool of the full-automatic ultrasonic cleaning machine is lower than the side vibration plate (the protruding part of the side plate in the length direction of the cleaning pool), the power knob should be turned to a small position to work for 2 to 3 minutes, causing the machine to fail to work normally or damage the equipment. In case of sudden power failure during operation, please turn off the power switch quickly and turn the power knob to a small position to avoid repeated power cut and transmission. It is strictly forbidden to start the machine, otherwise it will cause serious injury to the washing machine.

打開電源開關前，將功率旋鈕逐漸旋到大處。關閉電源時，然后再關閉電源。當被清洗工件浸沒于清洗溶液中時，超聲波以強大的空化效果作用于工件的內外表面，故其特別適合于復雜多孔、不能有硬物擦洗的光潔表面。

Before turning on the power switch, turn the power knob gradually to a large position. Turn off the power before turning it off. When the cleaned workpiece is immersed in the cleaning solution, the ultrasonic wave acts on the inner and outer surfaces of the workpiece with a strong cavitation effect, so it is especially suitable for the smooth surface with complex pores and no hard objects to scrub.

以上就是今天為大家介紹的關于問題以及注意事項的全部內容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站www.nianyankeji.cn，我們的工作人員會及時與您取得聯系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website www.jnthcsb COM, our staff will contact you in time.